Brand : EVEROX
Model : EMB-1360-1565-2065
FEATURES:
1. Hi-rigidity machine structure designs and the main casting is made of meehanite cast iron which is annealed perfectly to eliminate internal residual stress.
2. Y, Z axis square rigid ways and dovetail slideway for saddle (X axis), furthermore, the all slideway be treated heat-treatment & precisely ground & scrapped etc.
3. Rugged stand & boxed structure column and integral heavy duty bed type designs and coupled reinforced ribs, advance machining servicing life & accuracy.
4. The spindle is made of SCM-21 steel and tempered stress relieved, carburized & precisely ground etc., and then, equipped with P4 level bearings, hi-precision.
Brand : MAC
Model : RPB-16X2000
The upper roll can move vertically as well as horziontally. It has double function of pre-bending and rounding.
The upper roll in drum-type, and support roll is added to the lower roll. Through regulations of the support roll, it can coil high precision.
Realize NC control and single-person operation. Simple & reliable, greatly raising efficiency.
Add up tapering reel and realize zero-piece coiling with great taper.
Vertical & horizontal motion of the upper roll is digitally indicated. Setting of motion scope is distinctive and
FEATURES:
1. The spindle headstock: 3-point support design for the spindle, and 4-step gear change (hyd. System). Main spindle gear driven is M6 spiral gear.
2. The high rigidity square way design for the X axis, and it can minimized the distortion which is caused by the overhang of slide cover.
3. The tailstock and quill are compacted with fully hydraulic operation. (The tailstock body forward and backward, clamp and unclamp, quill extend and retract) The quill diameter is?250mm (9.842?) and it is rotatable. The center taper MT6 is standard. And the manual tailstock lubrication is standard.
4. Floor type bed, 3V guide way design, the Z axis ball screw is mounted at front side of the bed. The optional of the second Z axis ball screw can be mounted at the rear side of the bed. The main feature is to reduce the displacement of cross slide.
FEATURES:
1. The spindle headstock: Equipped 3-step gear change (hyd. System) Spindle bore: ?130mm, ?160mm, ?180mm, ?255mm, ?305mm.
2. Dovetail type guide way design for X axis, it can be maximized the swing over cross-slide diameter.
3. Manual tailstock, quill dia. ?165mm, MT6 for center taper and the manual tailstock lubrication system are all standard.
FEATURES:
1. The bed is adopted hi-rigidity rib structure design & coupled with hi-tensile meehanite cast-iron which is annealed treatment to eliminate internal residual stress, the bed way is high frequency heat treated, precision ground etc.,
2. Three-point support on the spindle and inspected by dynamic balancing, the spindle gear is module 3 & wide, this is very suitable to do heavy duty cutting and being with 3-step speed shifting. Especially, that can output by full power even as the spindle speed at low gear, large cutting force.
3. The carriage is coated with Turcite-B which provides low friction & vibration and ensures smooth movement & accuracy.
4. Adopted central lubrication system which can be lubricated slide way & ball screw. The headstock is adopted forced lubricating & oil bathed combined.
5. Manual tailstock coupled with 1:1 & 1/4:1 feed shifting.
6. The visual window of sliding safety door is adopted the reinforced glass at inner layer and the out layer is polycarbonate, this device can be protected the failure workpieces and be hi-safety.
Standard Accessories
U sleeve ?16,20,25,32 per size 1 pc
ID sleeve ?6,8,10,12,16,20,25 per size 1 pc
OD tool holder 2 sets
ID tool holder 3 sets
U-drill tool holder 1 sets
MT#2, 3 sleeve per size 1 pc
Work light
Full enclosure
Heat exchanger
Auto lubricator
Hydraulic chuck (1 set hard jaw, 3 sets soft jaw)
Programmable tailstock
Side type chip conveyor (with tank)
Tool box with tool kits
Optional Accessories
Auto door
Auto bar feeder
Air-conditioner
Tool probe
Oil-water separator
Oil skimmer
Part catcher
Standard Accessories
U sleeve ?12,16,20 per size 1 pc
ID sleeve ?6,8,10,12,20 per size 1 pc
OD tool holder 2 sets
ID tool holder 4 sets
U-drill tool holder 2 sets
MT#2, 3 sleeve per size 1 pc
Work light
Full enclosure
Heat exchanger
Auto lubricator
Hydraulic chuck (1 set hard jaw, 3 sets soft jaw)
Manual tailstock
Back type chip conveyor (with tank)
Tool box with tool kits
Optional Accessories
Auto door
Auto bar feeder
Air-conditioner
Tool probe
Oil-water separator
Oil skimmer
One piece molding and 30? slope designed to make the lathe stronger, more durability, more stable, and less deformed.
Use Meehanite Casting, be grinded accurately, and be made by high-frequency heat treatment.
Standard Accessories
U sleeve ?12,16,20 per size 1 pc
ID sleeve ?6,8,10,12,20 per size 1 pc
OD tool holder 2 sets
ID tool holder 4 sets
U-drill tool holder 2 sets
MT#2, 3 sleeve per size 1 pc
Work light
Full enclosure
Heat exchanger
Auto lubricator
Hydraulic chuck (1 set hard jaw, 3 sets soft jaw)
Manual tailstock
Back type chip conveyor (with tank)
Tool box with tool kits
Optional Accessories
Auto door
Auto bar feeder
Air-conditioner
Tool probe
Oil-water separator
Oil skimmer